Fire Damper Testing Co.Get a quote
Pages ▾

Smoke Damper Testing

Motorised fire and smoke dampers driven closed and open from the panel, with the actuator, the position switches and the link to the fire alarm checked as part of the same visit.

Get a quote
Metal ductwork running through a building

What applies to smoke dampers

  • StatuteFire Safety Order 2005, article 17: systems kept in efficient working orderSource: legislation.gov.uk
  • Test intervalAt least every 12 months, with system checks betweenSource: BESA guidance
  • Ask forA result per damper for closing, opening and signalSource: BESA VH001 reporting
  • Design rulesApproved Document B for dampers in ductworkSource: gov.uk

Why motorised dampers need a different test

A spring damper has one job: fall shut when its link melts. A motorised damper is wired into the building. It closes when the fire alarm tells it to, it may reopen to clear smoke, and it reports its position to a panel. Each of those links can fail without the blades themselves being faulty.

That is why smoke damper testing is a separate line in most quotes. The tester needs to understand the control side as well as the ductwork, and the visit usually has to be planned with whoever looks after the alarm or building management system.

What a smoke damper test covers

  • A command test. The damper is driven closed from the panel or local test switch and the tester confirms it actually closed.
  • Fail-safe. Power to the actuator is removed to check the damper goes to its safe position on its own.
  • Position switches. The open and closed signals reach the panel and match what the blades are doing.
  • The alarm link. Where it can be done safely, the alarm signal is simulated to prove the cause and effect works.
  • The damper itself. The same visual checks as a fire damper: fixing, fire-stopping, cleanliness and access.

Dampers in smoke control systems

In buildings with a smoke extract system, some dampers are meant to open in a fire, not close. Testing those without the system designer's cause and effect chart is guesswork. Before the visit, find the fire strategy or the commissioning records so the tester knows what each damper is meant to do.

The design rules for where dampers go in ductwork sit in Approved Document B. The test only proves the installed damper works; it does not tell you whether the right damper was fitted in the first place. If the report raises that question, it goes back to your fire risk assessor.

Common faults found on motorised dampers

  • Actuators that run but have slipped on the spindle, so the blades do not move.
  • Position switches out of adjustment, so the panel shows closed when the damper is open.
  • Dampers left disconnected after building work, with nobody noticing on the panel.
  • Blades held by dust or debris, especially in kitchen and workshop extracts.

Fixing these is usually quick once found. Larger repairs and replacements are covered on the maintenance and repairs page, and spring dampers on the fire damper inspection page.

Smoke damper testing questions

Is a smoke damper the same as a fire damper?

Not quite. A fire damper stops flames passing along a duct. A smoke damper is built to limit smoke leakage, and in a smoke control system it may need to open as well as close. Many modern units are rated for both and called fire and smoke dampers.

Can motorised dampers be tested without going into the ceiling?

They can be driven from the panel, and many systems report their position back. A physical look is still needed to confirm the blades really moved and that the damper is clean and fixed properly.

Who needs to be there on the day?

Often the fire alarm or building management contractor, because the test means putting the alarm interface into a test state. Agree who is attending before the date is booked.

How often should smoke dampers be tested?

The same interval as fire dampers, at least once a year (BESA guidance). Smoke control systems often have their own weekly or monthly function checks on top.

Arrange smoke damper testing

Give us the building postcode and who to speak to. A damper count, a recent report or a ceiling plan all help the firm price it, but none of that is needed to start.

We look for a damper testing firm that works in your area and let you know which one before anything else happens. Your details reach that firm only once you agree, and there is no charge to you.

Your building and contact details
Get a quote