Fire Damper Inspection
The yearly check of every fire damper in the ductwork: found, looked at, closed, reset and photographed, with a written result for each one.

The rule behind the annual inspection
- StatuteFire Safety Order 2005, article 17: equipment kept in good repairSource: legislation.gov.uk
- Test intervalAt least every 12 months, more often in dusty ductsSource: BESA guidance
- Ask forA damper-by-damper report with open and closed photosSource: BESA VH001 reporting
- ScotlandFire (Scotland) Act 2005 in place of the OrderSource: legislation.gov.uk
What a fire damper inspection is for
A fire damper is a steel shutter inside a duct where it passes through a fire-resisting wall or floor. Most of the time it stands open so air can move. When the heat of a fire melts its fusible link, or a signal from the alarm tells it to, it shuts and stops fire travelling along the duct into the next compartment.
Because it sits inside the duct, usually above a ceiling, nobody sees it from one year to the next. Dust builds up on the blades, springs weaken, links get painted over and installers fix things to the duct that stop the blades moving. The inspection is the one time anyone checks that it would still work.
What the tester checks at each damper
A thorough inspection covers the damper and the wall around it, not just the blades:
- That the damper is where the drawings say, and that its asset tag matches the register.
- That the frame is fixed into the wall or floor and the gap around it is properly fire-stopped.
- That the fusible link or actuator is intact and has not been painted, wired or taped open.
- That the blades and the duct either side are clean enough to close.
- That there is a way in: an access panel in the duct and in the ceiling below it.
How the drop test works
For a spring-operated damper the tester releases the link by hand and watches the blades fall shut. They check that the damper closes fully and latches, then reopen it, fit a new or reset link and check it again. Motorised dampers are driven shut from the control panel instead, which is covered on our smoke damper testing page.
Intumescent dampers have no moving parts to drop. They get a visual check of the honeycomb and the fixing, and the report should say so rather than record them as tested.
What a good report shows
The report is the reason you are paying for the visit, so ask to see a sample before you choose a firm. It should have:
- One line per damper with its tag, location, type and size.
- A photo of the damper open and another closed.
- A clear result: pass, fail or no access, never a blank.
- The defect and a recommended repair for every fail.
- The date, the tester's name and the next due date.
BESA guidance explains why the frequency and the record matter. Our test log template shows the columns to expect.
Getting the building ready
Two things make the biggest difference to the price and the result. First, find whatever drawings you have, even old ones, because they cut the time spent hunting for dampers. Second, tell the firm about ceilings that cannot be opened, rooms that are locked or areas that can only be reached out of hours. A damper the tester cannot reach is recorded as no access and still has to be dealt with.
If you have never had a test, expect the first visit to cost more. After that the register exists and the yearly test is quicker. For typical figures, see the fire damper testing cost guide.
Fire damper inspection questions
What is the difference between a fire damper inspection and a drop test?
An inspection is the look: is the damper there, fixed properly, clean, labelled and reachable. The drop test is the proof that it closes. A proper annual visit does both at every damper it can reach.
How long does a fire damper inspection take?
A damper behind an access panel takes a few minutes to test and reset. Allow far longer where ceiling tiles have to come out or a tower is needed, and add time on a first visit for finding and tagging everything.
Does the building have to be empty?
No, but the areas being tested need clear access and the ventilation may be switched off for short periods. Offices and schools often book evenings or holidays for that reason.
Who keeps the report?
The responsible person for the building. It should go into the fire safety records and be available to your fire risk assessor. See the regulations page for who that is.
Book your damper inspection
Give us the building postcode and who to speak to. A damper count, a recent report or a ceiling plan all help the firm price it, but none of that is needed to start.
We look for a damper testing firm that works in your area and let you know which one before anything else happens. Your details reach that firm only once you agree, and there is no charge to you.
Your enquiry has arrived.
From here:
- We pick a damper testing firm for the building's area and send its name to your inbox.
- You reply yes or no. Nothing is shared before your reply.
- The firm phones or emails about damper numbers, drawings and access times, then prices the job in writing.